China ATA Shaft Mounted Helical Gear Box for Conveyor helical double gearbox

Merchandise Description

ATA Shaft Mounted Helical Gear Box for Conveyor

ATA series shaft mounted gearbox(speed reducer) with helical hardened gears has the characteristics of substantial carrying capability, clean transmission, light excess weight, low energy intake and so on. Input shaft of ATA velocity reducer is connected with gear motor by belt pulley, hollow output shaft is joined with a key. It can be replaced by electric powered drum as energy for belt conveyors and lifting equipments. ATA collection shaft mounted gearbox could be connected with back again-stop to steer clear of the working equipment back skating, and conveniently mounted by tie rod. ATA series shaft mounted velocity reducer is widely used in the mining equipments, concrete mixing batching plant, stone crushers, sand creating manufacturing line and other belt conveyors, mechanical transmission places.
Mechanical belt conveyors generate technique is composed of ATA shaft mounted speed reducer, torque arm, pulleys and gear motors, whose power transmission from the gear motor to the gearbox by way of the pulley, and then pace reducer handed to the drive pulley via the hollow output shaft and the gearbox is fastened by torque arm, anti-slip unit can be configured. The system is practical to put in, use and maintain.

The features of ATA shaft mounted gearbox:
Mounting Sort: Tie rod Hanging shaft mounted
Output Shaft: One essential hollow shaft, each design can pick 3 hollow diameter at most.
Gearbox Housing: Hard Iron Steel, can be utilized outside the house.
Anti-slip unit: Can go well with for any product, It is very convenient to be mounted.

The purposes of ATA shaft mounted gearbox:
Agriculture, commerce, telecommunications market, the food sector, tobacco business, vehicle sector, cement business, mining sector, mixing station belt conveyor program.

The maintenance of ATA shaft mounted gearbox:
one. Ahead of starting the reducer need to be crammed of N159 or N220 extreme stress industrial equipment oils, until the gearbox oil shows an intermediate placement
two. Right after 3 months working, the gearbox require to modify oil, consideration it have to be particles inside the device rinse ahead of introducing new oil.
three. At the reducer hollow shaft finishes and travel pulley stop gland plate should mounted with locking screws.
four. The reducer pulley and the motor pulley have to be parallel when they are mounted and the belt tightness ought to be moderate.

The designs of ATA shafted mounted gearbox:
ATA35 ATA40 ATA45 ATA50 ATA60 ATA70 ATA80 ATA1

If you have any demand from customers for our items please come to feel cost-free to contact me. 


/ Piece
|
1 Piece

(Min. Order)

###

Application: Motorcycle, Industry
Function: Speed Changing, Speed Reduction
Layout: Parallel
Hardness: Hardened
Installation: Torque Arm Type
Type: Circular Gear

###

Customization:
Available

|


###

Rated Power Intput Speed Output Speed Ratio Installation Form
1.1~193KW 500~1400r/min 25~300r/min IN=5.0…31.5 Shaft mounted

###

Model ATA30 ATA35 ATA40 ATA45 ATA50 ATA60 ATA70 ATA80 ATA100 ATA125
Permitted Torque 180Nm 420Nm 9501Nm 1400Nm 2300Nm 3600Nm 5100Nm 7000Nm 11000Nm 17000Nm

/ Piece
|
1 Piece

(Min. Order)

###

Application: Motorcycle, Industry
Function: Speed Changing, Speed Reduction
Layout: Parallel
Hardness: Hardened
Installation: Torque Arm Type
Type: Circular Gear

###

Customization:
Available

|


###

Rated Power Intput Speed Output Speed Ratio Installation Form
1.1~193KW 500~1400r/min 25~300r/min IN=5.0…31.5 Shaft mounted

###

Model ATA30 ATA35 ATA40 ATA45 ATA50 ATA60 ATA70 ATA80 ATA100 ATA125
Permitted Torque 180Nm 420Nm 9501Nm 1400Nm 2300Nm 3600Nm 5100Nm 7000Nm 11000Nm 17000Nm

What Is a Helical Gearbox?

Basically, a gearbox is a rotating circular machine part that consists of toothed components, which mesh together. Its function is to transfer speed and torque to other parts of the machine. It is also similar to a lever, and operates on the same principle.helical gearbox

Double helical gears

Having a helical gearbox has many advantages, including higher efficiency, high strength, and a superior gear system. However, it has its drawbacks. One of these drawbacks is the axial thrust. Axial thrust is not a problem with single helical gears, but it is a problem with double helical gears.
In double helical gears, there are two sets of teeth that are arranged in a V-shape. In one set of teeth, there is a groove that enables the axial force to be cancelled out. The groove eliminates the need for thrust bearings and allows for efficient handling of high capacity power transmission.
Aside from the axial thrust, there are also issues with face contact. Asymmetric load sharing and oscillation put substantial alternating loads on the shaft bearings. These alternating loads can lead to early bearing failure.
Fortunately, helical gears are smoother than spur gears, which means they can withstand more load. They also have greater pitch circle diameter than spur gears. However, they are limited in their scope. The pitch error distribution on the helical gears is typically limited to 50 mm peak-to-peak amplitude. It is important to control the phase difference of oncoming gears with high accuracy.
Typically, the helical gears that are used in a gear box are assembled from the same module. This allows for interchangeability of components and economical construction. A normal module set can use the same tooth-cutting tools that are used for spur gears.
Double helical gears are used in power transmission in fluid pumps and gas turbines. They are also commonly used in planetary reduction gear boxes for engines in civil aviation.
Generally, double helical gears are larger than single helical gears. They are typically generated from a special generator. They are also more expensive.
However, manufacturers are looking to find gears that are more convenient to use. One solution is to manufacture double helical gears on a multi-tasking machine tool. This allows the gear to be machined in complicated shapes.
The multi-tasking machine tool can also modify the tooth surface. This is useful for 3D printing helical gears with a high level of accuracy.helical gearbox

Crossed-axis helical gears

Several factors affect the performance of crossed-axis helical gears. One of the important factors is the position of the gears on the cross shaft. The gears will not perform properly if they are not oriented in a different direction.
Crossed-axis helical gears have a special situation, in which they will not function properly if the gears are oriented in the same direction. This is especially true for automobile oil pump/distribution shafts. Depending on the situation, gears will operate as a normal helical gear or as a spur gear.
Compared to spur gears, crossed-axis helical gears have relatively higher capacity. However, the transverse contact ratio of these gears is reduced. This decrease is dependent on the pressure angle. The pressure angle affects the curvature radii of the teeth. In addition, the length of the contact line is reduced. This shortens the efficiency of the gear.
Helix angle of crossed-axis helical gears is 45 degrees. It may be a left-handed or a right-handed gear. The pitch circle diameter of a helical gear may be big compared to that of a spur gear. This is due to the fact that the gears are cut at an angle to the shaft.
In the axial direction, the meshing of helical gears is very similar to spur gears. However, there are a few design rules to optimize these gears.
The first rule is that the gears must be staggered in opposite directions. If the gears are not staggered, the contact lines cannot be changed.
The second rule states that the pitch of a helical gear is dependent on its helix angle. It is possible to calculate the pitch circle of a helical gear, by integrating along the face width. In addition, the length of the contact lines decreases as the pressure angle increases. However, this decrease is not as large as that of a spur gear.

Right angle helical gears

Choosing a right angle helical gearbox can be difficult. With so many types, sizes, and configurations to choose from, it can be difficult to figure out which one is right for your application. The key to choosing the right gearbox is understanding your application and what factors are most important to you.
For example, if you are looking for a gearbox that can be used in a high-speed, high-torque application, the most important consideration is the efficiency of the product. Right-angle gearboxes are compact and easy to maintain, making them ideal for high-torque applications.
Some applications that require high-torque gears include pulp and paper manufacturing, food processing, mining, and car washes. Some of the advantages of right angle gears include high efficiency, low maintenance, and low noise. If you are in the market for a right angle helical gearbox, make sure to select a supplier that can provide you with a wide range of options.
Right-angle helical gearboxes come in several different bevel configurations. Spiral bevel gears require precision and are difficult to manufacture. However, they can be used interchangeably. Spiral miter gears are designed to rotate in the same direction as the input shaft, which helps ensure a smooth, direct transfer of power.
If you are considering a helical gearbox for a high-speed application, you will need to know your preferred input/output ratio. The standard ratios are 1:1 and 2:1. If you need a step-up ratio, you can install an additional output shaft opposite the input shaft.
Other benefits include lower running noise, superior strength, and durability. Because they are made of larger teeth, helical gears are less likely to wear out. Also, helical gears provide higher power carrying capacity.
To determine which type of right angle gearbox is best suited for your application, you should discuss your needs with your supplier. They should be able to offer a wide range of options, including custom solutions. They should also provide you with a list of past clients and online reviews.
To find a right angle helical gearbox that can meet your needs, it’s important to understand the various design features. For example, you should make sure that your gearbox has a self-locking capability, which means that the load cannot drive the worm. Having a self-locking gearbox also means that you do not need to install a braking system.helical gearbox

Spiral teeth

Using helical gearboxes to drive a motor car or truck is an efficient method of power transmission. However, the efficiency of this method depends on the helix angle of the gear. The helix angle is the angle that the gear teeth are cut at.
Helical gearboxes may be of different helix angles, depending on the specific gear set. The helix angle can vary between 15 and 30 degrees. This is important because the helix angle has a significant effect on the position of tooth contact. If the contact is not in a proper position, then there will be a large amount of vibration. This will affect the speed of the gear.
Helical gearboxes can be of two types: crossed axis and parallel axis. Crossed axis gears are usually used to connect parallel shafts. They have the same center gap as spur gears. On the other hand, parallel axis gears are usually used to drive a motor. The difference between the two types of gearboxes is their design and arrangement.
In addition to the helix angle, the gears may have different fillet, teeth, and radius. This means that the gear will have different NVH characteristics. In addition, there are different types of spiral teeth that may be used in the gearbox.
Hypoid gears are also similar to spiral bevel gears, but they differ in that the axes of the gear shaft do not intersect the axis of the hypoid gear. The hypoid gear exerts a very high thrust load on the bearings.
When compared to a straight bevel gear, the hypoid gear experience a smoother, less noisy operation. They also produce less shock loading.
Spiral bevel gears are also designed to produce less vibration. They are also more cost-effective. However, they require a larger diameter to transmit the same torque. This can lead to a reduced mechanical efficiency and lower fuel economy.
The best spiral bevel gears can carry a higher thrust load than straight teeth. This is why they are preferred for applications that require heavy load efficiency.
They are also appreciated for their NVH characteristics. They are also a quieter option for applications that require high speed. Helical gears can be used in many different industries. The food, automotive, and oil industries are examples of these types of gears.
China ATA Shaft Mounted Helical Gear Box for Conveyor     helical double gearboxChina ATA Shaft Mounted Helical Gear Box for Conveyor     helical double gearbox
editor by CX 2023-04-03